Discussion Humanities Assignment Help

Please see the attached instructions.

I have completed the paper, however, it needs to changes and I need help with that. Below is the note from the instructor:

“How does this relate to HIM or health informatics? You need to modify your topic and title and title for the next component of the project so it is appropriate for the HIM research project. the focus of your project needs to include something related to HIM.”

Please use the paper I have completed and incorporate HIM/Health Informatics to it. Maybe It can be Cancer treatment and the use of Technology such as Electronics Health Records, or something similar, please get creative and find something related to health informatics.

1-If there is a perfect air mixing, what is the Kmix equal to? Tell me where you find the information.

2-What’s the typical Kmix value for industrial ventilation?

3-IAQ control application to control CO: An automobile garage was contaminated with carbon monoxide. You only have a carbon monoxide meter available and need to use dilution ventilation to control workers over-exposure to CO. If you measure 3500 ppm of CO in the room before turning on dilution ventilation system, and 2000 ppm after 5 minutes of dilution ventilation. Please determine the total time that will take to reduce CO concentration from 3500 ppm to TLV level so that workers will not be overexposed? Assume the room conditions and dilution ventilation system don t change. Hint: use equation 21B in page 4-14.

4-IAQ control application to control temperature: During the summer, the temperature in a large warehouse reaches a steady-state temperature averaging 35 F greater than the outside temperature when the dilution volume flow rate is Q of 50,000 cfm. What volume flow rate would be required if you want to lower the temperature difference to 10 F? Hint: use equation 22 in page 4-15 and example 4-9.

5-What is the TLV for acetone? You need tell me both the TLV value and where you find the value (e.g. online link).

6-A factory located in Colorado has an assembly facility located at the altitude of 5,000 ft and temperature of 70 F. Please use two different methods to determine the df (3 decimals). You must show your calculation processes or show me where to find the answer, and include appropriate unit for full credit.

7-The factory in Colorado is using acetone as solvent, which can be emitted uniformly at the rate of 7 lbs / hour into the plant atmosphere environment. What is q, the emission volume flow rate for acetone? Hint: You need to decide which equation to use (equations 14 and 15 in page 4-3).

8-The factory in Colorado will use a dilution ventilation system to control the average airborne acetone concentration in the factory no more than the 50% of the TLV. Assume a perfect air mixing exists in the factory. What is the dilution air volume flow rate, Qd, needed for the ventilation system. Hint: You firstly need to determine which equation (16 and 17 in page 4-5) to be use.

9-The factory in Colorado has an assembly room of 250,000 cubic feet. Please determine the air change rate (N, ACH) needed to control airborne acetone concentration under 50% TLV. Hint: You need firstly determine which equation of 19 to be used.

10-If the air mixing Kmix is 3 in the Colorado factory, please recalculate Qd and N needed to control airborne acetone concentration under 50% TLV. Other factors (250,000 cubic feet, altitude of 5,000 ft, temperature of 70 F, uniform emission rate of 7 lbs / hour) remain the same.

11-A chemistry lab with 22,000 cubic feet was contaminated with hydrogen sulfide. If dilution air is provided for 15 minutes, what will the average H2S concentration be? Assume STP, q = 0, C1 =1,500 ppm, Kmix = 1.0, and Qd = 2000 scfm.

I would expect to see some type of hazard vulnerability study or analysis for Utah in the paper. You should also include a discussion on some of the area resources.

• Paper outline should address the following:

· Abstract – An overview of the paper topic, importance of the topic etc. Begin your abstract with “The purpose of this discussion is to…”

· Targeted topics – Sample paper subheadings, major areas to be covered in your paper. Use bullets to help separate each subheading.

· Selected references – cite at least three at this point (but will need to cite more in final paper). Also, see “Annotated Bibliography” below.

· Expected conclusions – what you expect at this point, recognizing that your final conclusions may be different; expect to discuss the difference(s) in your final paper.

Students should have selected your company and a case your company has litigated (or is litigating) for your Legal Case Analysis. Please provide a brief summary for that case.

The summary should state the name of the case, facts that led up to case, and generally what the case is about. Students should use the IRAC method that we have used previously in class.

Students should be able to describe the case as if you are an employee describing the case to your employer or an employer explaining the case to your legal management team. You can use the format below.

LEGAL CASE ANALYSIS (SUMMARY)

Case Name

Facts 5 to 7 sentences

Issue 1 sentence

Rule/Area of Law 1 to 2 sentences

Parties’ Argument 1 to 2 sentences for each

MLA

Note: Please let me know which company and case are you gonging to select before you start.

I will invite you to do the whole legal case analysis later, so please stay online.

Thanks